FOR SALE 1969 Plymouth Road Runner 3 Speed Auto
- Thread starter petertom
- Start date
- Status
Rapid Transit
Just A Traveler In Time
https://www.69roadrunner.net/mopar/...69-rr-built-sept-1968.6796/page-2#post-198274
Can anyone give me some input on the lap belts and retract lengths??
The shoulder harness are not a concern. I've got that correct.
What catches my attention at this point is the seat belts in this car.
Which is something I'm dealing with.
Any help would be appreciated.
Those aren't correct latches. (note male end).
The won't function with the factory sun visor clips.
Seems to be a common new aftermarket type in this car. (aircraft?)
I've got all my originals that I took off 3 years ago.
The only think I can find are the shoulder harnesses.
I can't find any of MY lap belts and wanted replacements anyway.
The car is in pieces and the seats and parts are all jammed up in storage.
This is what I bought and the lap belts and retracts seem short.
Front lap belts are approximately 36 inches and the retracts are 12.
https://pgclassic.com/products/1850-69ben-100?_pos=2&_sid=f29f76d23&_ss=r
I'm concerned what I've bought are too short
@Russ69Runner help?
Post 33.
https://www.69roadrunner.net/mopar/...69-rr-built-sept-1968.6796/page-2#post-198292
Can anyone give me some input on the lap belts and retract lengths??
The shoulder harness are not a concern. I've got that correct.
What catches my attention at this point is the seat belts in this car.
Which is something I'm dealing with.
Any help would be appreciated.
Those aren't correct latches. (note male end).
The won't function with the factory sun visor clips.
Seems to be a common new aftermarket type in this car. (aircraft?)
I've got all my originals that I took off 3 years ago.
The only think I can find are the shoulder harnesses.
I can't find any of MY lap belts and wanted replacements anyway.
The car is in pieces and the seats and parts are all jammed up in storage.
This is what I bought and the lap belts and retracts seem short.
Front lap belts are approximately 36 inches and the retracts are 12.
https://pgclassic.com/products/1850-69ben-100?_pos=2&_sid=f29f76d23&_ss=r
I'm concerned what I've bought are too short
@Russ69Runner help?
Post 33.
https://www.69roadrunner.net/mopar/...69-rr-built-sept-1968.6796/page-2#post-198292
Last edited:
SomeCarGuy
Well-Known Member
I bought seat belts about 18 months ago. It was a supplier and not a retailer like YO or classic. They seem ok but may not be oem perfect correct. The shoulder harnesses clip to those sun visor pieces and are a separate deal. I also ordered a set of shoulder belts to convert my car but haven’t yet been brave enough to cut the headliner.
Russ69Runner
Well-Known Member
Did not thing you had to cut the head liner to install those clips for the seat belts. Should be a set of screw holes just too the side of the sun vizor. Use a heat gun to stretch the head liner. Screw holes next to front set straight up also in inner frame rail behind head liner.
Rapid Transit
Just A Traveler In Time
Correct.
The shoulder visor clips screw on with the visors.
Heads up.
The repos appear to be stainless and not chrome plated.
Even though they are an "authorized" reproduction.
My chrome ones were rusty and I'm fine with the stainless.
My headliner has a few wrinkles.
So do I but maybe the ones in the head liner will work out over time.
The shoulder visor clips screw on with the visors.
Heads up.
The repos appear to be stainless and not chrome plated.
Even though they are an "authorized" reproduction.
My chrome ones were rusty and I'm fine with the stainless.
My headliner has a few wrinkles.
So do I but maybe the ones in the head liner will work out over time.
- Status